英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

rippling    音标拼音: [r'ɪpəlɪŋ] [r'ɪplɪŋ]
n. 涟漪

涟漪

rippling
n 1: a small wave on the surface of a liquid [synonym: {ripple},
{rippling}, {riffle}, {wavelet}]


请选择你想看的字典辞典：
单词字典翻译
rippling查看　rippling　在百度字典中的解释百度英翻中〔查看〕
rippling查看　rippling　在Google字典中的解释Google英翻中〔查看〕
rippling查看　rippling　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Are there standard tolerances for dimensional lumber?
    3 I understand that the actual dimensions of dimensional lumber are slightly smaller than their nominal dimensions, like how a 2x4 is actually 1½" x 3½" Are there industry standard tolerances on how close a board needs to be to those sizes? When I search for this, I get results about tolerances for framing and assembly, not the boards
  • Using new lumber in an old wall with larger lumber dimensions
    5 I am trying to widen the doorway to a room in a house that was build in 1905 the framing is 16 on center, however the lumber is wider than a standard 2x4 by about a 1 2 inch (the actual dimensions of the wood are 2x4) I can position the jackstuds so that they are flush with the wall of the room, but that would leave a gap on the other side
  • Insulated Basement. Poured Concrete with 2-in. Interior Rigid Foam . . .
    Air sealing is imperative The connection between concrete foundations and wood framing is a place prone to air leaks and moisture problems Wood is often warped, and concrete is rarely flat There are at least three places for air to leak in and probably a lot more Leaky connections can mean energy, moisture, comfort, and IAQ problems Extending the wall sheathing past these connections is a
  • AdvancedFramingGuide-BE - Green Building Advisor
    “The current industry standard wall – a 2x4 frame at 16-inch centers with double top plates, three stud corners, jack studs, cripples and double headers – is being replaced by a 2x6 frame at 24-inch centers with single top plates, two stud corners, no jack studs, no cripples and single headers (and in many cases no headers at all)
  • plumbing - Can I install a wall mount toilet here? - Home Improvement . . .
    Here are the dimensions measured after I opened the wall Before opening the wall I made my peace with the idea that I will be installing a normal toilet because: -I thought the wall is built with
  • 2-0 Plan layout with wall elevation - GreenBuildingAdvisor
    The whole point of advanced framing, also known as optimum value engineering (OVE), is to frame a house so that it meets its structural requirements without wasting material A welcome corollary is that the same house will have more room for insulation inside the walls and will therefore be more energy efficient than a conventionally framed house Minor downsides, for example, attaching trim
  • Proper size of header to support new door in load bearing wall?
    AKA: 2 x 4 is 1 1 2 x 3 1 2 = 5 25 sq in A 2X6 = 8 25si So you'd need 2 2x4's to replace a 2x6 A simple call to a decent Planning Dept would answer that question 1) Over-building always gives you a good impression with the inspectors 2) Asking the Inspector first gives them the added impression you're trying to do things right!
  • Confirming Door Jam Dimensions for Thick Walls - GreenBuildingAdvisor
    Ideally, door jamb should be as wide as wall but door jambs are generally made for 2x4 or 2x6 walls, not for 2x6, plus thickness of exterior insulation and rainscreen Not sure a door company would even make a custom door with such a wide jamb but if they did it would likely be very expensive In the past, I just get a door for 2x6 wall and add extension jambs myself in the field
  • real dimensions of 2 by 4 in inches centimeters
    A dimensional 2x4 is 1 5 inches x 3 5 inches The reason being, 2x4 describes the rough dimensions before the boards are milled down to their "dimensional" (flat even) size So you start with a rough 2"x4" board that might be somewhat warped, crooked, rough, etc then it is passed through the mill, where it is planed cut down to the final smooth flat hopefully not warped 1 5"x3 5" Note that
  • Framing deep overhangs air-sealed single pitch roof - GreenBuildingAdvisor
    Any advice on the 3ft cantilever on the high side? Was thinking of sistering on 2x4s to the rafters Would maybe go to 2x6, but with 2x4 on the flat on top I’d be getting into a much larger fascia than I’d like… Thanks again!





中文字典-英文字典  2005-2009