英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
120568查看　120568　在百度字典中的解释百度英翻中〔查看〕
120568查看　120568　在Google字典中的解释Google英翻中〔查看〕
120568查看　120568　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Colt style 9mm mags not locking in lower (Fixed) - AR15. COM
    I'm using ASC mags on an 80% lower with a Hahn block my mags don't lock into the lower very well If you pull on them hard they will come out It's like the little nub is not long enough to go throug
  • [ARCHIVED THREAD] - Mag seating issue with AP5 *Resolved*
    So I inserted a mag and pressed on the opposite side of the mag release button and could tell it’s not fully seated My question: If I remove the magazine catch can I “tune” it like a AR-15 mag release? Tighten or loosen ‘till it is in it’s sweet spot?
  • Bolt Catch issues gt; Troubleshooting gt; AR15. COM
    Quoted: Two different issues If the rifle will not hold open after the last round, then the magazine spring is not lifting the bolt catch up This is very common when the bolt catch roll pin hole is under sized, and tight on the pin Remove the upper from the lower, and press on the bottom of the bolt catch Does it rotate freely, and snap back into position being pushed by the bolt catch
  • Bolt Catch issues w Pmags + Advice Needed - AR15. COM
    Question Potential Issue #2- "Mag Catch" So I started thinking hard and being every single M3 and M2 fit differently in the magwell and yield different results (all 2013 production M2 and M3 Pmags btw, even if they were produced in the same month), I was thinking if the Mag Catch gripped the mags tighter, or a tad differently, if that may help
  • Trying to decide the cause of the bolt catch not engaging . . .
    Here's the issue I'm having I was always under the assumption that using your magazine as a monopod was a bit no no until watching some videos by Travis Haley and some others saying if everything is
  • Magazine Not Seating - HELP! gt; Troubleshooting gt; AR15. COM
    Take a close look at the magazine catch inside the mag well, is it protruding into the mag well sufficiently to catch a magazine? Yes I would say it sticks out roughly 1 8"
  • Mag stuck, bolt catch stuck gt; General Discussion gt; AR15. COM
    [ARCHIVED THREAD] - Mag stuck, bolt catch stuck (Page 1 of 2) Home General General Discussion
  • AR9 mag catch help, options? gt; Rimfire and Pistol Calibers gt; AR15. COM
    It only happens with the round feeding from the left side of the mag, never the right side After inspecting closely I found the mag doesn't lock in the new 9mm lower as far up as it does in the AR-15 lower which causes the bold to not catch and strip the left round from the mag reliably
  • Adjusting the mag catch to allow the mag to seat deeper gt; AR . . . - AR15. COM
    What appears to be happening is the followers on the pmags are not as high as the Lancers, causing the rounds to contact the fed ramps My question is, can you modify the mag catch to allow the mag to seat a bit deeper, or higher if you will
  • First build, mag catch issues. gt; Troubleshooting gt; AR15. COM
    Hence some mag lips are thicker and will bottom out against the bottom of the carrier before the slot catch point is high enough for the catch lip to actually lock into as well As for once the mag catch is installed, just look into the mag well to determine if the hook point of the catch is protruding into the receiver deep enough





中文字典-英文字典  2005-2009